Formwork ties hold the two faces of a wall or column form together against the pressure of wet concrete, so the wall stays the right thickness. They fall into two groups: ties that are left in the concrete and snapped or cut off, and ties that are pulled out after the pour and reused. Which one you choose depends on the finish, whether the wall must be watertight, and how many times the forms will be reused.
What does a formwork tie do?
Wet concrete pushes outwards on the form faces. A tie runs through the wall between the two faces and carries that pressure in tension, while walers and plates spread the load across the form. Ties also set the spacing between the faces, which fixes the wall thickness.
Types of formwork ties
| Tie type | How it works | After the pour |
|---|---|---|
| Snap tie | A rod with ends held by tie holders on the outside of the form | Snapped off at a weak point; the middle stays in the wall |
| Flat tie | A thin steel strap locked to the forms with a wedge and pin | Broken off at a notch; single use |
| Loop tie | A bar with looped ends locked with a wedge | Left in the concrete |
| Fibreglass tie | A glass-fibre and resin rod held with a gripper | Cut flush with the surface; left in the concrete |
| Threaded tie (tie bar) | A threaded bar with nuts or wing nuts and plates on each side | Pulled out and reused if it runs through a plastic sleeve |
| Taper tie | A tapered threaded rod, greased before use | Pulled out whole and reused |
| She-bolt tie | An inner rod joined to two removable she-bolts | Inner rod stays in; she-bolts are reused |
| Coil tie | An inner member with coils, connected to external bolts | Inner member stays in; bolts are reused |
Sources: The Constructor, Build Construct.
Left-in ties vs removable ties
- Left-in ties (snap, flat, loop, fibreglass) are quick to fit and need no sleeve. Part of the tie stays in the wall, so the holes may need patching.
- Removable ties (threaded, taper) cost more at first but are reused many times. A sleeve or cone leaves a clean hole that is filled after striking.
- Internal disconnecting ties (she-bolt, coil) are a middle route: a cheap inner part stays in the wall and the costly outer parts are reused.
Accessories that go with ties
- Wing nuts and plates: tighten the tie against the walers and spread the load.
- Sleeves and cones: let a tie bar be withdrawn and leave a neat hole.
- Stop end ties: hold a stop end at the edge of a pour, such as our Timber End Tie.
- Hole plugs: blank off tie holes in panels that are not in use, such as our Panel Hole Plugs.
How to choose a formwork tie
- Follow the temporary works design. Tie type, size and spacing come from the formwork design, because ties carry the concrete pressure.
- Match your panel system. Framed panels often take a specific tie and fixing.
- Think about the finish. Visible walls may need a tie that leaves a small, neat hole.
- Think about water. Basements and tanks may need a tie detail that limits water paths through the wall.
- Count the reuses. Many pours with the same forms favour removable ties.
For the wider picture, read formwork accessories explained.
Related guides: types of formwork · how to fix a stop end · formwork striking times
Buying for this job?
OM Private Ltd supplies Timber End Ties, Panel Hole Plugs, formwork clamps (including Claw Head), and all formwork accessories to sites across the UK.
Request a trade quoteCall +44 7452 889827
Trade prices on any quantity · UK-wide delivery · Quote requests 24/7
Frequently asked questions
What is the most common type of formwork tie?
Snap ties and threaded tie bars are both widely used. Snap ties suit quick, single-use work; threaded tie bars with sleeves suit system formwork that is reused many times.
Can formwork ties be reused?
Some can. Taper ties and sleeved threaded ties are pulled out and reused. Snap, flat, loop and fibreglass ties stay in the concrete, so they are single use.
What is a she-bolt?
A she-bolt is a removable outer part of a tie that screws onto an inner rod. The inner rod stays in the wall and the she-bolts are taken off and reused.
Who decides tie spacing?
The formwork designer, as part of the temporary works design. In the UK, temporary works are managed under BS 5975-1:2024 and BS 5975-2:2024.
Need ties and fixings for a pour? Browse formwork accessories or request a quote.
